Difference between revisions of "Projects:LED Sign"
Jump to navigation
Jump to search
m (AlexN moved page LED Sign to Projects:LED Sign) |
|||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
==LED Sign== | ==LED Sign== | ||
[[File:2016-07-02 11.01.26.jpg|400px|thumb]] | |||
In about mid 2016 the makerspace received about 6 of these LED signs. They are large arrays of LEDs that can be programmed to display messages. They currently have pre-programmed messages related to buses, as that is what they were previously used for. | In about mid 2016 the makerspace received about 6 of these LED signs. They are large arrays of LEDs that can be programmed to display messages. They currently have pre-programmed messages related to buses, as that is what they were previously used for. | ||
The challenge put forth is: figure out how to program them directly without the use of a card-reader or the original software. | The challenge put forth is: figure out how to program them directly without the use of a card-reader or the original software. | ||
In late 2019, a member from the [https://www.amherstmakerspace.com/ Amherst Makerspace] came and took a couple of the signs to reverse-engineer them. The succeeded where we did not! The documentation is up on [https://hackaday.io/project/168796-hacking-a-luminator-bus-sign Hackaday.io] for all to read! | |||
*Luminator LED Sign | *Luminator LED Sign | ||
| Line 13: | Line 17: | ||
*Chip on board: Winbond W78F052C40DL | *Chip on board: Winbond W78F052C40DL | ||
Other chips: | Other chips on the boards: | ||
* | *74HC595D | ||
* | *HC2450 | ||
*MAX....something | |||
Notes: | Notes: | ||
| Line 31: | Line 36: | ||
*Data Dumps from sniffing the UART line on an internal microcontroller: | *Data Dumps from sniffing the UART line on an internal microcontroller: | ||
**[https://drive.google.com/ | **[https://drive.google.com/open?id=0BzAXZ8qTt-CoeE9CX1NOQmZEZW8 Google Drive Link] | ||
*[http://pdf1.alldatasheet.com/datasheet-pdf/view/182797/WINBOND/W78E052C40DL.html Datasheet of IC on controller chip] | *[http://pdf1.alldatasheet.com/datasheet-pdf/view/182797/WINBOND/W78E052C40DL.html Datasheet of IC on controller chip] | ||
[[Category: Projects]] | |||
Latest revision as of 17:35, 7 February 2020
LED Sign
In about mid 2016 the makerspace received about 6 of these LED signs. They are large arrays of LEDs that can be programmed to display messages. They currently have pre-programmed messages related to buses, as that is what they were previously used for.
The challenge put forth is: figure out how to program them directly without the use of a card-reader or the original software.
In late 2019, a member from the Amherst Makerspace came and took a couple of the signs to reverse-engineer them. The succeeded where we did not! The documentation is up on Hackaday.io for all to read!
- Luminator LED Sign
- Model #: 510648001 Rev B
Display board:
- FW: MBUSMC-8-V2.2
- MBUSMS-8 07.5
- Chip on board: Winbond W78F052C40DL
Other chips on the boards:
- 74HC595D
- HC2450
- MAX....something
Notes:
- The main source of data seems to be the Winbond chips that are on the control panel circuit board and the LED board with the serial and RJ45 connectors on it
- The signs can be connected together in a Master/Slave configuration so one will display the data from the other
- Attempts at putting a data sniffer inbetween two signs in a Master/Slave config did not seem to work. The addition of the sniffer seemed to interfere with the signal itself.
- Data was extracted from the Tx pin on the Winbond chip. It doesn't appear to have any particular pattern. The data dump can be found in Resources below.
Resources:
- Data Dumps from sniffing the UART line on an internal microcontroller: